Nov 03, 2025 Leave a message

How to perform daily maintenance, weekly maintenance, and monthly maintenance on the SMT machine

1-day maintenance (1) The technician guides the operator to stop the machine and perform daily maintenance work 10 minutes before starting work every day. (2) Use a clean white cloth to clean the dust on the surface of the machine, including the body surface, monitor, keyboard, mouse, buttons, switches, etc. If necessary, use a piece of cloth dipped in soapy water to wipe the surface of the machine. It must be wrung dry without dripping water before use, and solvents such as alcohol and dishwashing water are not allowed to be used for cleaning. (3) Check if the air pressure has reached the 0.5MPA pressure value. (4) Check if the PCB conveyor belt runs smoothly, and use the PCB for testing without any jamming. (5) Check if all * * devices are functioning properly, including the front and rear * * doors, FEEDER floating high SENSOR, and also check if the area SENSOR is functioning properly. Test the functions of each SENSOR while running and paused, and ensure that the SENSOR alarm status is displayed on the screen. (6) Use a vacuum cleaner to clean the scattered components inside the machine. (7) Clean the dust on the LASER SENSOR VCS lens with lens paper. (8) Warm up the machine and listen for any abnormal sounds before starting production. (9) Daily maintenance precautions: ① If any abnormal situation is found during inspection, it should be immediately reported to the technician for handling; ② When cleaning scattered components, do not use an air gun to blow them down onto the machine board, as this may cause circuit faults; ③ Maintenance should be carried out while the machine is stopped; ④ When cleaning the laser sensor, it is not allowed to wipe it with unclean and rough objects; SMT surface mount machine 2. Weekly maintenance (1) First, perform a spot check to check for leaks in the air distribution pipe and joints, and whether each unit cylinder is working properly. (2) Check whether the conveyor belt, pulley, and stopper are damaged, and repair or replace them immediately if they are damaged. (3) Remove all NOZZLE from ATC and clean them with ultrasonic waves (adding alcohol to the ultrasonic waves). After about 5 minutes, remove them and blow them clean with a wind gun. Then, apply a small amount of 1 # oil to the movable plug on the head with a cotton swab. Pay attention to cleaning the NOZZLE with 505, 506, 507, 508, etc., and make sure the rubber head is facing up and not stained with alcohol. (4) After wiping the ACT slider clean with a white cloth, add a small amount of 1 # engine oil to the fixing screw of the movable slider. (5) Use a white cloth strip to clean the cylinder, belt, slider, and width adjustment thread of the conveyor, and add a small amount of 1 # engine oil on the stopper and pulley. Add a small layer of printing butter on the width adjustment thread. (6) Clean the XY linear guide with a white cloth strip and reapply a thin layer of printing butter. (7) Clean the laser window with lens paper. (8) Retest all NOZZLE within SET UP and save to exit. (9) Check the LASER curve in the manual menu and wipe it clean. (10) After slowly warming up the front cover for 2 minutes, use a white cloth to wipe off excess butter. (11) Weekly maintenance precautions: ① During the maintenance process, all belts must not be contaminated with grease. ② Do not add too much oil to NOZZLE after cleaning. ③ LASER WINDOW should not be cleaned with any chemical solvents. ④ After maintenance, the NOZZLE on ATC should be returned to its original position. 3. Monthly maintenance (1) Turn off the machine power. (2) Wipe off all NOZZLE sleeves of the working head with a 1.5M internal angle and replace all Filters. (3) Clean all dust on the sensors with a white cloth strip. (4) Use a vacuum cleaner to clean the dust inside the distribution box, and if necessary, clean the boards piece by piece. Use a cleaning agent to clean them and dry them with a blower before reinstalling them. (5) Remove the vacuum generator, disassemble and clean it, wipe off the dirty grease inside with a white cloth, clean the body with a cleaning agent and blow it clean, then reapply sealing oil to the sealing ring and reassemble it. (6) Clean the X, Y, and Z axis guide rails and screws with a white cloth. Except for the Z-axis guide rail and screw, add AFL oil, and add EP2 butter to all other guide rails and sliders. (7) Remove the mouse and clean the internal dirt with a white cloth. (8) Turn on the machine and warm it up for 5 minutes, then wipe off any excess butter with a white cloth. (9) Monthly maintenance precautions: 5. How to carry out daily, weekly, and monthly maintenance of the reflow soldering furnace? 1. Daily maintenance: (1) Check whether the conveyor chain has lubricating grease, and add lubricating grease in a timely manner if necessary. (2) Check if there are any running edges on the transport network. If there are running edges, notify JT in a timely manner. (3) Check if the drive roller of the reflow soldering furnace entrance network belt has shifted. If there is any displacement, adjust it according to the steps of loosening screws adjusting locking screws. (4) Check if the conveyor belt drive roller at the outlet of the reflow soldering furnace is loose. If it is loose, adjust it by following the steps of loosening screws adjusting locking screws. (5) Check if there is an appropriate amount of high-temperature oil in the oil cup, with the oil level 5mm away from the cup mouth. If necessary, add high-temperature oil in a timely manner. 2. Weekly maintenance: (1) Check the surface of the transport belt for dirt adhesion. If there is any dirt adhesion, wipe it with alcohol in a timely manner. (2) Check for any foreign objects in the groove of the guide rail chain. If there are any foreign objects, remove the chain and wipe it with alcohol in a timely manner. (3) Check whether the bearings of the driven gears in the transport chain are flexible, and add lubricating oil in a timely manner if necessary. (5) Check whether there is lubricating grease and no foreign objects on the surface of the screw rod of the machine head components. If necessary, wipe it clean in a timely manner and add lubricating grease. (6) Check for FLUX and dust on the rectifier plates in each area of the furnace. If there is dust, clean it with alcohol in a timely manner. (7) Check if there is any vibration or noise during the operation of the lifting motor of the furnace lifting system. If there is any vibration or noise, it should be replaced in a timely manner. (8) Check if the filter of the exhaust device is blocked. If there is any blockage, clean it with alcohol. (9) Check if there is any FLUX adsorption on the rectifier board in the cooling area of the cooling system. If there is FLUX, it should be cleaned with alcohol in a timely manner. (10) Check the surface of the photoelectric switch at the transportation entrance for dust accumulation. If there is dust accumulation, it should be wiped clean with a soft dry cloth in a timely manner. (11) Check whether the surface of the PC and UPS is clean. If there is dust accumulation, it should be wiped clean with a soft dry cloth in a timely manner. 3. Monthly maintenance: (1) Check for any vibration or noise during transportation, and notify JT promptly if necessary. (2) Check for any looseness in the fixing screws of the transportation motor. If there is any looseness, tighten the screws. (3) Check if the tension of the transmission chain is appropriate, and adjust the motor positioning screw in a timely manner if necessary. (4) Check for burnt objects and black powder on the transportation chain. If any are found, they should be removed and cleaned with diesel in a timely manner. (5) Check the positioning of the synchronous axis for width adjustment in the active end track and whether the fixing block is loose. If there is any looseness, it should be locked in time. (6) Check if the positioning screw of the hot air motor is loose, and if it is loose, lock it in time. (7) Check for dust and foreign objects in the control box of the electrical system. If there are any foreign objects, cut off the power and blow out the dust and foreign objects with the same pressure air.

Send Inquiry

whatsapp

teams

E-mail

Inquiry