Aug 10, 2022 Leave a message

Main Process Parameters Of Wave Soldering Equipment

The quality of wave soldering products is directly related to the control of wave soldering process parameters. The process control of wave soldering is the main factor that directly affects the welding quality of electronic products. Here we mainly share the main process parameters related to wave soldering equipment.

1. Wetting time of wave soldering circuit board

Wave soldering wetting time refers to the minimum time for wetting after the solder joints are in contact with the solder. This time exists only in theory and cannot be measured in practice.

2. Wave soldering circuit board residence time

The time from contacting the wave crest surface to leaving the wave crest surface of a solder joint on the PCB is the dwell time, also known as the soldering time. The formula for calculating the dwell time is: dwell time = wave width/speed. Usually, the dwell time should not be too short, otherwise the pad will not reach the necessary wetting temperature. Generally, the dwell time is controlled within 2 to 3 seconds.

3. Preheating temperature of wave soldering equipment

The preheating temperature refers to the temperature reached before the PCB is in contact with the wave crest surface. The temperature of the PCB soldering surface should be determined according to the germanium production characteristics of the soldering.

4. Welding temperature of wave soldering circuit board

The soldering temperature of wave soldering equipment is a very important soldering parameter, which is usually 50-60°C higher than the melting point of the solder (183°C). In most cases, it refers to the temperature of the solder pot. Appropriate solder temperature can ensure that the solder has good fluidity. The soldering temperature should be checked regularly after the wave soldering machine is started. Especially when the number of soldering defects increases, the temperature of the solder pot should be checked first. In actual operation, the temperature of the soldered PCB solder joints is lower than the temperature of the soldering pot, which is the result of the heat absorption of the PCB.

5. Wave height of wave soldering equipment

The wave height refers to the tin-eating depth of the PCB during wave soldering, and its value is usually controlled between 1/2 and 2/3 of the thickness of the PCB. Too deep will cause the molten solder to flow to the surface of the PCB, resulting in "bridging". In addition, the deeper the PCB is immersed in the solder, the more obvious the effect of blocking the solder flow, and the effect of the component pins will disturb the flow velocity distribution of the solder, and the relative zero-speed movement of the PCB and the solder flow cannot be guaranteed. For oversized and overweight PCBs, it is usually solved by adding tin strips or erecting steel wires on the tin pot of the wave soldering machine.

6. Wave soldering circuit board transmission inclination

When installing the wave crest equipment, in addition to placing the machine horizontally, the inclination of the conveyor should also be adjusted. The inclination of the high-end wave crest machine is usually controlled at 3° ~7° between. By adjusting the inclination angle, the soldering time between the PCB and the wave crest can be regulated, and the appropriate inclination angle is conducive to the faster peeling of the liquid solder from the PCB and returning to the tin pot.

7. Hot air knife technology of wave soldering equipment

The wave soldering hot air knife is a new technology that appeared in the 1990s. The so-called hot air knife is a narrow and long "cavity" with an opening placed under the MA just after the SMA leaves the soldering wave. The opening of the cavity can blow out a high-pressure airflow of 500-525 °C, which is like a knife, so it is called For the hot air knife.

The high-temperature and high-pressure airflow of the hot air knife blows the solder joints on the SMA that are still in a molten state, which can not only blow off the excess solder, but also fill up the shortage of solder in the metallized holes, and the bridged solder joints can be repaired immediately. At the same time, because the melting time of the solder joints can be extended, the original solder joints with pores can also be repaired.

In short, the hot air knife can greatly reduce welding defects and has been widely used in SMA welding. The temperature and pressure of the hot air knife should be set according to the component density on the SMA, the component type and the orientation on the PCB.

The wave solder joint formation process: when the PCB enters the front end of the wave surface and passes through the wave solder shock wave, the substrate and the pins are heated, and before leaving the wave surface smooth wave, the entire PCB is immersed in the solder, that is, it is bridged by the solder, but At the moment of leaving the end of the wave, a small amount of solder adheres to the pad due to the wetting force, and due to the surface tension, it shrinks to a minimum state centered on the lead, at this time between the solder and the pad The wetting force is greater than the cohesive force of the solder between the two pads. This results in a plump, rounded solder joint, excess solder leaving the tail of the wave, falling back into the tin pot due to gravity. The formation of wave solder joints is very related to the seven process parameters of the above wave soldering equipment. The use of wave soldering equipment must understand the above seven process technical parameters.


Send Inquiry

whatsapp

teams

E-mail

Inquiry